MX MTB CO. / Learn

THE RIDE LAB.

A practical starting point for bike care, fitness, and riding progression. Pick a topic, find your level, and take one useful idea to your next ride.

15 guides

Maintenance / Beginner

The five-minute pre-ride check

Catch small problems before they become a long walk home.

Read guide

Start with air

Before a ride, inspect both tires for cuts, damage and unusual wear. Check pressure with a gauge, using the tire and rim manufacturers' limits and your setup guidance rather than a universal number. Confirm both wheels are properly secured using the axle manufacturer's procedure. A soft tire or loose wheel is a reason to stop and investigate.

Test brakes and drivetrain

Squeeze each brake separately while walking the bike. Both should engage reliably. Look over the chain, cassette and chainring for dirt, damage or obvious problems, then shift through the gears during a short controlled test ride. Check that your handlebar and saddle are secure. Do not solve an unfamiliar loose component by tightening it as hard as possible; use its specified torque.

Finish before the trailhead

Pack a pump, compatible tube or repair supplies, multitool, water and a charged phone. Try your brakes and steering in a safe open area before joining the trail. If braking is weak, a part is cracked, or something still moves when it should not, have a mechanic inspect it. The goal is repeatability: use the same check before every ride, especially after transporting the bike.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Riding skills / Beginner

Ride centered. Brake smoothly.

Build control with a balanced stance and a simple stopping drill.

Read guide

Set up a practice space

Use a flat, open, traffic-free area with predictable grip and plenty of stopping room. Wear a fitted helmet and check the bike first. Confirm which lever operates each brake; do not assume every bike is arranged the same way. Adjust lever reach only according to the brake instructions so you can brake without stretching your fingers.

Let the bike move

Coast with pedals level, weight supported through your feet, and elbows and knees relaxed. Look ahead along your intended path instead of staring at the front tire. For rough ground, rise off the saddle and increase the bend in your limbs. Stay mobile rather than locking your arms or hanging far behind the bike.

Practice controlled stops

Mark a braking point and roll toward it slowly. Apply both brakes progressively, increasing pressure smoothly while keeping the wheels rolling. Repeat at the same modest speed until you can stop predictably without skidding. A front brake is useful braking equipment, not something to avoid; abrupt grabs are the problem. Move to gentle terrain only when the basic drill feels routine. If the wheels lock, reduce pressure and reset. Stop the session if fatigue makes your braking or posture inconsistent.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Riding skills / Intermediate

Corner with confidence

Choose your line early and give your tires time to grip.

Read guide

Read the corner

Practice after you can brake reliably and maintain a relaxed standing position. Start with a wide, familiar turn. Inspect its surface, exit and runout: loose gravel, wet roots, exposure and a tightening radius all change what is appropriate. Choose a conservative entry speed. Do not use someone else's pace as your reference.

Look through the turn

Do most of your slowing before the turn, while the bike is upright and traction is predictable. Look along the path you want to follow and toward the exit, checking near hazards without fixating on them. Keep elbows and knees flexible so you can let the bike lean beneath you. A flat turn, banked berm and off-camber corner do not demand identical body positions.

Use a repeatable drill

Set two widely spaced markers in an open area and ride gentle turns between them. Repeat both directions, prioritizing smooth entry and a controlled exit over speed. Progress to a mild berm only after your flat-ground control is consistent. If a turn surprises you, slow progressively rather than making a sudden brake grab while leaned over. Walk a corner with exposure or uncertain grip. A qualified coach can help you refine bike-body separation and foot position for the particular terrain.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Maintenance / Beginner

A quieter, cleaner drivetrain

Clean the chain, apply the right lubricant, and wipe off the excess.

Read guide

Prepare the bike

Support the bike securely so the drivetrain can turn freely. Gather clean rags, a suitable brush or chain-cleaning tool, bicycle-compatible cleaner and the correct lubricant for your chain system. Check chain wear with a compatible gauge before cleaning; cleaning will not reverse wear. Follow the chain maker's instructions if you use a wax-based system.

Remove dirt before adding lube

Clean the chain and dirty drivetrain surfaces with compatible products, keeping cleaner and lubricant away from brake rotors and pads. Work methodically around the whole chain rather than adding oil on top of grit. Follow the cleaner's rinsing instructions and dry the chain before lubricating. Use separate cleaning tools for the drivetrain and braking surfaces.

Lubricate, then wipe

Apply a small amount of purpose-made chain lubricant to the rollers, rotate the drivetrain to distribute it, and follow the product's settling instructions. Wipe away surplus lubricant from the outside of the chain; a visibly wet exterior collects dirt. Inspect the drivetrain after wet or dusty rides and clean according to conditions rather than a rigid mileage promise. Persistent noise, skipping or a damaged link deserves diagnosis. Never spray lubricant toward a disc brake or try to cure brake squeal with oil.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Maintenance / Beginner

Practice a tube change before you need one

A home practice run makes a trailside flat much less stressful.

Read guide

Carry compatible supplies

Bring a tube that fits your wheel and tire, tire levers and a suitable pump. Learn your axle system at home. This overview covers a conventional tire-and-tube repair; tubeless plugs, inserts and damaged sidewalls need their own compatible procedures. Move completely off the trail before starting and keep small parts together.

Find the cause

Remove the wheel according to the bike instructions. Deflate completely, move the tire bead into the rim's center channel and lift one bead with proper tire levers. Remove the tube, then inspect the tire and rim carefully for the object or damage that caused the puncture. Do not use a knife or screwdriver as a tire lever, and avoid blindly sweeping fingers over sharp debris.

Refit and verify

Give the replacement tube enough air to hold its shape. Fit it without twists and seat the bead carefully without trapping the tube. Inflate gradually, checking that the bead sits evenly around both sides. Respect the lower applicable tire or rim pressure limit. Reinstall and secure the wheel correctly, then test the brake before riding. Avoid squeezing a hydraulic brake with its wheel removed unless the proper spacer is installed. Walk out if the casing, rim or retention system is damaged.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Maintenance / Intermediate

Know when your disc brakes need attention

Inspect wear and contamination before attempting a repair.

Read guide

Start with symptoms

A change in stopping power, persistent squeal or an unusual lever feel calls for inspection. Let brakes cool before touching nearby parts. Keep fingers and tools clear of spinning rotors. Stop riding if a brake cannot stop the bike reliably or you suspect a hydraulic leak; a noisy brake and a failing brake are not the same diagnosis.

Check the correct specifications

Identify the brake and rotor models and consult their manuals for wear limits, pad compatibility and service steps. Measure pad material accurately rather than guessing from a photograph. Manufacturer limits differ, so a general online threshold is not a substitute for the applicable specification. Check rotor wear using the manufacturer's method too. Oil, grease and some cleaning products can contaminate pads.

Choose the right next step

A pad replacement requires correct pad orientation, retention hardware, compatible compound and any specified bedding-in procedure. Hydraulic bleeding and piston problems may be better handled by a qualified mechanic. Do not combine an unfamiliar brake fluid with an existing system. Keep lubricant away from rotors and pads throughout maintenance. After any service, verify wheel retention and brake operation in a controlled area before returning to technical terrain. Save the correct manual so future inspections use the same reference.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Bike setup / Intermediate

Find your suspension baseline

Use the correct model guide, record settings, and change one thing at a time.

Read guide

Identify what you own

Find the exact fork and shock model, year and serial number. Air springs, coil springs and different damper generations use different procedures. Begin with the bicycle and suspension manufacturers' current setup guidance. RockShox riders can use TrailHead for supported starting settings. Do not copy a friend's pressure, sag percentage or rebound clicks merely because you weigh about the same.

Establish a baseline

Use the prescribed pump and follow the model's air-spring equalization procedure where applicable. Wear your usual riding gear when a setup procedure calls for rider weight or sag. Record pressure or spring details, rebound, compression and any model-specific recommendations. Never exceed component limits. Treat a suggested starting setting as a baseline, not a guarantee that the bike is correctly tuned for every trail.

Test something repeatable

Choose a familiar, low-consequence trail and notice grip, support and how the bike settles after bumps. Change one permitted external setting at a time, make a small adjustment, and repeat the same section. Log what changed and restore the baseline if the result worsens. Stop if you notice oil loss, unusual play or sudden performance changes. Internal servicing requires the correct manual, tools and expertise; this guide covers external setup, not disassembly.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Tricks & progression / Intermediate

Manual foundations: control before distance

Learn a small, controlled front-wheel lift before chasing a long manual.

Read guide

Meet the prerequisites

A manual means rolling on the rear wheel without pedaling. Begin only when you can stand comfortably on level pedals and operate the rear brake . Choose a flat practice area, wear a helmet and suitable protection, and learn with a qualified coach . Avoid traffic, steep slopes and hard obstacles during early practice.

Work on a small lift

At low speed, start centered, lower your body to load the bike, then move your hips back as the bike moves forward beneath you. Use body movement rather than a sudden arm yank. Start with the front wheel barely leaving the ground and return it smoothly. Keep a finger covering the rear brake and practice using it to bring the front wheel down before attempting greater height.

Build consistency

Use a painted or chalk line as a timing target instead of a hard obstacle. Repeat small lifts, keeping pressure balanced left to right. Progress comes from predictable control, not a single long attempt. If the front wheel twists or you lose pedal contact, reset and reduce the movement. Stop before fatigue changes your coordination. A manual is a useful foundation, but it is not the correct automatic response to every drop or obstacle.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Tricks & progression / Intermediate

Bunny hops: learn the sequence

Separate front-wheel and rear-wheel movement before adding an obstacle.

Read guide

Begin below your limit

Practice after you can brake predictably, balance while standing and make a small controlled front-wheel lift. Use a flat, open space with a clear runout. A line on the ground is a better first target than a curb, log or rock. Wear a fitted helmet and appropriate protection; coaching can make the timing easier to understand.

Link two movements

First, load the bike with your legs and use a small manual-style movement to bring the front wheel up. As that wheel rises, extend upward and slightly forward to unweight and raise the rear wheel. Keep the movement controlled instead of pulling desperately on the handlebar. Allow your arms and legs to absorb the landing, staying balanced over the bike.

Make the drill measurable

Practice each wheel movement separately, then work on clearing the same ground line with both wheels. Aim for repeatable timing and a calm landing, not maximum height. Only add a small, forgiving obstacle when the sequence is reliable. Do not use clipless pedals to conceal a lack of control by hauling the bike upward. If you hit the target repeatedly or land unpredictably, return to the ground-line drill. Stop when tired, and leave trail obstacles with consequences for a later, coached progression.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Tricks & progression / Expert

Expert progression: make a jump plan

A readiness and inspection framework for coached jump sessions—not a send-it checklist.

Read guide

Check readiness, not confidence alone

Expert is a content category, not permission to attempt a feature. Jumping requires reliable braking, body control and wheel-lift skills, plus a bike approved for the intended use. Confirm the bike is sound and use suitable protective equipment. Work with a qualified coach at an appropriate skills area before moving toward larger jumps or unfamiliar features.

Inspect the entire feature

Walk the approach, takeoff, landing and runout from a safe position. Determine whether it is a rollable tabletop or a mandatory gap. Check surface damage, obstacles, traffic, weather and the consequences of coming up short or going long. Do not assume a previously ridden feature is unchanged. A text guide cannot prescribe a safe speed for an unseen jump.

Progress one variable at a time

Establish repeatable takeoff and landing control on a small feature selected with your coach. Repeat rather than immediately increasing size, speed and complexity together. Decide your stopping point before fatigue arrives, and stop if conditions or confidence change. Keep advanced rotations, flips and high-consequence gaps out of self-taught progression. Review a session with your coach: identify what stayed consistent, what broke down, and which foundational drill to practice next. Walking past a feature is a useful decision, not a failed ride.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Fitness / Beginner

Build fitness for more trail time

Combine manageable riding, basic strength work and recovery.

Read guide

Start with your current capacity

Choose riding you can complete comfortably and consistently. Use easy terrain while building endurance so fatigue does not force difficult handling decisions. Include a gentle warm-up before harder effort. If you are returning from injury, have a relevant medical condition, or are unsure how to start, work with an appropriate health professional or qualified trainer.

Add strength without rushing

Mountain biking uses leg strength, trunk control and upper-body stability as well as aerobic fitness. Learn simple squat, hip-hinge, step-up and trunk-stability movements with good technique before increasing resistance. Begin with manageable sessions and stop or modify exercises that cause pain. Off-bike training supports riding; it does not replace time practicing balance, braking and line choice.

Balance effort and recovery

Build gradually and avoid increasing ride length, intensity and strength load all at once. Alternate demanding days with easier activity or rest, and watch whether soreness or tiredness is affecting your handling. Log how sessions feel rather than judging progress only by speed. Bring enough water and food for the planned outing and conditions. An achievable routine you repeat is more useful than a punishing week followed by a long break. This is a general framework, not a personalized training or rehabilitation prescription.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Trail essentials / Beginner

Be the rider people are glad to meet

Good trail manners protect access and make shared spaces better.

Read guide

Check before rolling

Ride only where bicycles are allowed and respect closures, private property and posted direction. A route appearing on an app does not establish legal access. Check the land manager or local trail organization for current conditions. Avoid damaging vulnerable wet trails and choose another route when riding would leave ruts.

Share the trail deliberately

Keep enough control to slow or stop for other people. Give a friendly greeting before passing and wait for a safe opportunity rather than squeezing through. On shared-use trails, yield appropriately to pedestrians and horses; downhill riders generally yield to uphill riders unless posted rules say otherwise. Around horses, slow down, speak calmly and follow the rider's guidance. Never chase wildlife or surprise animals at speed.

Leave the place better

Stay on the established route, do not cut switchbacks, and walk an obstacle instead of creating a bypass. Pack out your litter and carry the supplies needed to be reasonably self-sufficient. Plan for weather, daylight and an emergency exit. Keep group stops off the riding line, especially below jumps or around blind corners. Consider joining a local trail organization or maintenance day. The best ride story includes how you treated the trail and the people sharing it.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Tricks & progression / Beginner

Slow down: your first balance drill

Build toward a trackstand with slow rolls, short pauses and easy foot-down resets.

Read guide

Choose a forgiving space

Use an open, traffic-free practice area with even ground and room to step off. Wear a helmet and use flat pedals while learning, or be completely comfortable releasing both feet. Before trying to balance nearly stationary, demonstrate a smooth start, controlled stop and reliable foot-down dismount. This drill develops control; it is not a contest to stay upright at any cost.

Roll, pause, reset

Roll slowly with hands on the grips and fingers ready at the brakes. Stand lightly on approximately level pedals, support your weight through your feet and keep elbows relaxed. Look forward rather than down at the tire. Gradually slow toward a brief pause, turn the front wheel slightly for balance and use small movements rather than rigidly freezing your body. Put a foot down whenever needed.

Build a repeatable habit

Practice several short pauses, resetting with an easy roll between attempts. Once those feel controlled, explore a small forward-and-back rocking movement to help maintain balance. Keep the goal modest: controlled movement and a calm exit matter more than duration. Stop before frustration or fatigue changes your posture. These general balance principles transfer from road-bike drills to mountain bikes; trail application comes later, away from exposure, traffic and other riders.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Fitness / Intermediate

Recover well. Ride better tomorrow.

Give each ride a purpose and leave enough room for recovery.

Read guide

Decide what today is for

Before riding, choose whether the session is easy endurance, focused skills or a harder workout. Keep an easy day genuinely easy instead of turning every climb into a race. For mountain biking, that may mean choosing smoother terrain so technical demands do not quietly turn recovery into a strenuous session. Follow your own plan rather than matching the fastest rider in a group.

Make recovery practical

Fuel and hydrate appropriately during the ride, finish with easy pedaling when practical, then eat and drink after the session. Protect time for sleep. Schedule easier days and lower-load periods instead of waiting until you feel exhausted. A recovery spin is optional: if it becomes another hard ride, it is adding work rather than meeting its purpose. Rest can be the better choice.

Notice the pattern

Keep brief notes on sleep, motivation, effort and how your legs feel. Several sessions of declining performance, persistent fatigue or unusual soreness warrant reducing load and reviewing the plan. Do not push through illness or use painkillers simply to hide warning signs. Seek appropriate professional advice for persistent symptoms. Progress is the ability to train and ride consistently over time, not proof that you can suffer through every planned workout.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Riding skills / Expert

Expert terrain: stay mobile on descents

Use inspection and adaptable body position before adding steepness or consequence.

Read guide

Separate the feature from the label

An expert trail rating does not tell you every move ahead, and ratings vary between trail systems. Inspect an unfamiliar technical section before committing. Identify the entrance, line, braking opportunities and exit, including whether a ledge is rollable or requires a drop technique. Walk features beyond your present ability. For exposed terrain or unfamiliar drops, work with a qualified coach rather than treating an article as clearance.

Stay balanced, not rigid

Keep pedals level when coasting, eyes scanning toward the intended exit, and joints ready to absorb terrain. Adjust your position to the slope while keeping useful pressure on both tires. Automatically hanging far behind the saddle can unload the front wheel and weaken steering. Allow the bike to move beneath you instead of locking your elbows and knees. Lower the saddle with your dropper when appropriate for movement clearance.

Practice below the consequence

Choose a familiar, low-risk section to rehearse transitions between a relaxed ready stance and a lower position for rough ground. Repeat it smoothly before increasing technical difficulty. A coach can identify whether braking, line choice or timing is the limiting skill. Add one challenge at a time, and stop when fatigue compromises control. The aim is a predictable descent, not merely getting through once.

Sources & further reading

Sources checked November 11, 2026. Check the linked source for updates.

Practice within your ability in a suitable area. For complex repairs or advanced features, get hands-on help from a qualified mechanic or coach. Manufacturer instructions take priority over general advice.